MSD DEUTSCH CONNECTOR KIT ***Use of Small Flat Blade Screwdriver for dis-assemble*** Electrical connectors; connectors; Deutsch; DT Series; Deutsch Pins; MSD Deutsch Connector Kit 360 Piece Deutsch Connector Kit comes with 2, 3, 4, 6, 8 and 12 Pole...

Connector, Deutsch,2-Pin,12ga. High Curr MSD MSD Deutsch Connector - 2-Pin - 12-14 Gauge Supplied with Terminals, Seals, and Housings There is absolutely no excuse for losing a race due to a poor wiring connection. MSD's Deutsch Connectors are sealed and...

Connector,Deutsch,2-Pin Connector Assemb MSD MSD Deutsch Connector - 2-Pin - 16-18 Gauge Supplied with Terminals, Seals, and Housings There is absolutely no excuse for losing a race due to a poor wiring connection. MSD's Deutsch Connectors are sealed and...

Connector,Deutsch,4-Pin Connector Assemb MSD MSD Deutsch Connector - 4-Pin - 16-18 Gauge Supplied with Terminals, Seals, and Housings There is absolutely no excuse for losing a race due to a poor wiring connection. MSD's Deutsch Connectors are sealed and...

Connector, 1-Pin Weathertight, 1/Card MSD MSD Weathertight Connector - 1-Pin - Qty 1 Self-Lubricating Silicone Seals for Protection Against Water, Dust, Oil, and Other Engine Compartment Fluids The Weathertight connectors are molded from a special nylon...

Connector, 2-Pin Weathertight, 1/Card MSD MSD Weathertight Connector - 2-Pin - Qty 1 Self-Lubricating Silicone Seals for Protection Against Water, Dust, Oil, and Other Engine Compartment Fluids The Weathertight connectors are molded from a special nylon...

Crank Trigger Pickup, Pro Mag, RCD MSD Crank Trigger Pickup - Non-Shielded - 3/8"-24 X 1.5" 36" Harness - Replacement - Use with MSD Flying Magnet Crank Trigger Kits Each pickup is wound on special bobbins and terminated to ur tinned conductor...

Crank Trigger Pickup, 3/8x1.5, Shielded MSD Crank Trigger Pickup - Shielded - Non-Magnetic - 3/8"-24 x 1.5" 32" Harness - Shielded Non-Magnetic Pickup The 3/8" diameter Pick-Ups are used with MSD's Sprint Car Crank Trigger systems as well as the...

Dist. Hold Down Clamp, Billet, Chevrolet Will not fit stock GM or aftermarket cast housing distributors._x000D_ Will not fit Street Fire distributor without modification. MSD Chevy Billet Distributor Hold Down Clamp The MSD Chevrolet Hold Down Clamp is...

Mounting Kit, Dzus Buttons, Sprint C MSD Pro Mag Points Box Mounting Kit for Sprint Cars MSD Pro Mag 12 Points box mounting plate. This Backing Plate Kit is for use with MSD Electronic Points Box PN 8106 or PN 81063MSD only. It is intended for use with...

Cap/Rotor Kit, GM V8 Vortec Dist Vortec Cap and Rotor Kit These caps offer a corrected position of the terminals to ease the routing of the wires. If the late '90's GM used a funky looking cap and rotor, commonly referred to as the Vortec Distributor...

Dist Cap, Chevy 6 Cyl, Clip Down 6 Cylinder Cap Chevy MSD 6 Cylinder HEI Distributor Cap w/Retainer These caps are injection molded from DuPont® Rynite material and feature spark plug-style terminals. MSD molds our distributor caps in-house. These...